|
Product Details:
|
| Product: | 1.45 Inch Full Color OLED | Resolution: | 160x128 Pixels |
|---|---|---|---|
| Display Mode: | Passive Matrix | Interface: | 8-bit 68XX/80XX Parallel, 4-wire SPI, I2C |
| Display Color: | Full Color | Optics: | All Viewing Angles |
| Outline Dim.: | 35.80 X 30.80 X 1.60 (mm) | Active Area: | 28.78 X 23.024 (mm) |
| Pixel Pitch: | 0.06 X 0.18 (mm) | Operating Temp: | -40°C To +70°C |
| Storage Temp.: | -40°C To +85°C | Driver IC: | SSD1333 |
| Supply Voltage For Logic: | 1.65 - 3.5V | Pin Number: | 30 Pins |
| Duty: | 1/128 | Compliance: | REACH & RoHS Compliant |
| Highlight: | 160x128 Pixels OLED Display,1.45 Inch OLED Display,30 Pins OLED Display |
||
1.45 Inch AMOLED 160x128 Dots 30 Pins Product Introduction
SFOS145TW-7100AN is a color OLED display. OLED (Organic Light Emitting Diode) is a new generation technology with brighter, clearer images and more agile response speed. This 1.45-inch SFOS145TW-7100AN OLED display consists of 160 x 128 monochrome dots. This OLED module is lightweight, low power consumption, small in size, and has different interfaces to choose from; It is the default SPI, parallel, and I2C interface.
The effective area size (diagonal) of this product SFOS145TW-7100AN is 1.45 inches, the module size is 35.80 x 30.80 x 1.60 (mm), and the effective area size is 28.78 x 23.024 (mm). This 1.45-inch OLED display is equipped with IC SSD1333 and has a high contrast ratio of 20000:1. The voltage range of the logic power supply is 1.65V-3.5V, with a typical value of 3V. It is very suitable for applications such as medical equipment, POS systems, white goods, home applications, industrial instruments, automation, audio-visual display systems, personal care products, household appliances, car displays, dynamic information displays, etc.
Display Specifications
1) Display Mode : Passive Matrix
2) Display Color : 262,144 Colors (Maximum)
3) Drive Duty : 1/128 Duty
Mechanical Specifications
1) Outline Drawing : According to the annexed outline drawing
2) Number of Pixels : 160 (RGB) × 128
3) Module Size : 35.80 × 45.30 × 1.60 (mm)
4) Panel Size : 35.80 × 30.80 × 1.60 (mm) including ”Anti-Glare polarizer”
5) Active Area : 28.78× 23.024 (mm)
6) Pixel Pitch : 0.06 × 0.18 (mm)
7) Pixel Size : 0.04 × 0.164 (mm)
8) Weight : TBD (g) ± 10%
1.45 Inch AMOLED 160x128 Dots 30 Pins Product Drawing
Pin Definition
| Pin No. | Symbol | I/O | Function | ||||||||||||||||||||||||
| PowerSuply | |||||||||||||||||||||||||||
| 22 | VDD | P |
Power Supply for Core Logic Circuit This is a voltage supply pin which is regulated internally from VCI. A capacitor should be connected between this pin & VSS under all circumstances. |
||||||||||||||||||||||||
| 5, 25 | VCC | P |
Power Supply for OEL Panel This is the most positive voltage supply pin of the chip. It must be connected to external source. |
||||||||||||||||||||||||
| 23 | VSS | P |
Ground of OEL System This is a ground pin. It also acts as a reference for the logic pins, the OEL driving voltages, and the analog circuits. It must be connected to external ground. |
||||||||||||||||||||||||
| 2, 29 | VLSS | P |
Ground of Analog Circuit These are the analog ground pins. They should be connected to VSS externally. |
||||||||||||||||||||||||
| Driver | |||||||||||||||||||||||||||
| 24 | IREF | I |
Current Reference for Brightness Adjustment This pin is segment current reference pin. A resistor should be connected between this pin and VSS. Set the current at 12.5μA maximum. |
||||||||||||||||||||||||
| 4, 27 | VCOMH | P |
Voltage Output High Level for COM Signal This pin is the input pin for the voltage output high level for COM signals. A tantalum capacitor should be connected between this pin and VSS. |
||||||||||||||||||||||||
|
3, 28 |
VSL
|
P
|
Voltage Output Low Level for SEG Signal This is segment voltage reference pin. When external VSL is not used, this pin should be left open.and diode to ground. |
||||||||||||||||||||||||
| TestingPads | |||||||||||||||||||||||||||
| 21 | FR | O |
Frame Frequency Triggering Signal This pin will send out a signal that could be used to identify the driver status. Nothing should be connected to this pin. It should be left open individually. |
||||||||||||||||||||||||
| Interface | |||||||||||||||||||||||||||
|
16 17 |
BS1 BS2 |
I |
Communicating Protocol Select These pins are MCU interface selection input. See the following table: |
||||||||||||||||||||||||
| BS1 | BS2 | ||||||||||||||||||||||||||
| I2C | 1 | 0 | |||||||||||||||||||||||||
| 4-wire SPI | 0 | 0 | |||||||||||||||||||||||||
| 8-bit 68XX Parallel | 0 | 1 | |||||||||||||||||||||||||
| 8-bit 80XX Parallel | 1 | 1 | |||||||||||||||||||||||||
| 20 | RES# | I |
Power Reset for Controller and Driver This pin is reset signal input. When the pin is low, initialization of the chip is executed. Keep this pin pull high during normal operation. |
||||||||||||||||||||||||
| 18 | CS# | I |
Chip Select This pin is the chip select input. The chip is enabled for MCU communication only when CS# is pulled low. |
||||||||||||||||||||||||
|
19 |
D/C# |
I |
Data/Command Control This pin is Data/Command control pin. When the pin is pulled high, the input at D7~D0 is treated as display data. When the pin is pulled low, the input at D7~D0 will be transferred to the command register. When the pin is pulled high and serial interface mode is selected, the data at SDIN is treated as data. When it is pulled low, the data at SDIN will be transferred to the command register. When 3-wire serial mode is selected, this pin must be connected to VSS. For detail relationship to MCU interface signals, please refer to the Timing Characteristics Diagrams. |
||||||||||||||||||||||||
| Interface | |||
|
14 |
E/RD# |
I |
Read/Write Enable or Read This pin is MCU interface input. When interfacing to a 68XX-series microprocessor, this pin will be used as the Enable (E) signal. Read/write operation is initiated when this pin is pulled high and the CS# is pulled low. When connecting to an 80XX-microprocessor, this pin receives the Read (RD#) signal. Data read operation is initiated when this pin is pulled low and CS# is pulled low. When serial mode is selected, this pin must be connected to VSS. |
|
15 |
R/W# |
I |
Read/Write Select or Write This pin is MCU interface input. When interfacing to a 68XX-series microprocessor, this pin will be used as Read/Write (R/W#) selection input. Pull this pin to “High” for read mode and pull it to “Low” for write mode. When 80XX interface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled low and the CS# is pulled low. When serial mode is selected, this pin must be connected to VSS. |
|
6~13 |
D7~D0 |
I/O |
Host Data Input/Output Bus These pins are 8-bit bi-directional data bus to be connected to the microprocessor’s data bus. When serial mode is selected, D1 will be the serial data input SDIN and D0 will be the serial clock input SCLK. Unused pins must be connected to VSS except for D2 in serial mode. |
| Reserve | |||
|
1, 30
|
NC | - |
Reserved Pin (Supporting Pin) The supporting pins can reduce the influences from stresses on the function pins. These pins must be connected to external ground as the ESD protection circuit. |
Absolute Maximum Ratings
| Parameter | Symbol | Min | Max | Unit |
| Supply Voltage for Operation | VDD | -0.3 | 4 | V |
| Supply Voltage for I/O Pins | VDDIO | -0.3 | 4 | V |
| Supply Voltage for Display | VDDH | -0.3 | 15 | V |
| Operating Temperature | TOP | -40 | 70 | .C |
| Storage Temperature | TSTG | -40 | 85 | .C |
| Life Time (100 cd/m2) | 10,000 | - | hour |
Optics Characteristics
|
Characteristics |
Symbol | Conditions | Min | Typ | Max | Unit |
| Brightness | Lbr | Note 5 | 100 | 120 | - | cd/m2 |
| C.I.E. (White) | (x) (y) | C.I.E. 1931 | 0.26 0.29 | 0.30 0.33 | 0.34 0.37 | |
| C.I.E. (Red) | (x) (y) | C.I.E. 1931 | 0.62 0.28 | 0.66 0.32 | 0.70 0.36 | |
| C.I.E. (Green) | (x) (y) | C.I.E. 1931 | 0.24 0.60 | 0.28 0.64 | 0.32 0.68 | |
| C.I.E. (Blue) | (x) (y) | C.I.E. 1931 | 0.10 0.16 | 0.14 0.20 | 0.18 0.24 | |
| Dark Room Contrast | CR | - | >10,000:1 | - | ||
|
Viewing Angle |
-
|
Free |
-
|
degree |
1.45 Inch AMOLED 160x128 Dots 30 Pins Product Image
Factory Facilities and Certifications
CONTACT US
Welcome to inquire via ck@saef.com.cn
Contact Person: Cologne Ke
Tel: +8613502983321
Fax: 86-755-2370-9419
